MicroMIX Series
M810 - Mixer/Amp - 2x 400w, 10 inputs
A new shape makes the M1610 and M810 the most versatile compact powered mixers on the market. The convenience, lighter weight and small ‘footprint’ of a box mixer with the tilt-back visibility and channel control access of a desk mixer makes these new ‘wedge’ mixers an ideal high power, high quality powered mixer solutions. High-powered high-efficiency class-H power amplifiers, newly designed input strips, on-board DSP and a new, more effective master EQ section and ten very useful and usable input channels complete the new ‘wedge’ mixer packages.
The 800-watt M810 has two integrated 400-watt power amplifiers that can be assigned as stereo mains, or mono main and mono monitor. Each amplifier is attached to an innovative master EQ section designed specificall y for these new mixers. The master EQ has a 9-band graphic EQ with additional high and low shelving EQ’s at either end of the frequency band. The nine graphic sliders are essentially all of the middle bands of a 15-band graphic EQ with the low and high frequency bands covered by separate shelving controls. This gives the user more control over the feedback-prone mid frequency bands; with high and low tone-shaping frequencies controlled by additional simple +/- 15 dB trim controls.

The M810 has 10 input channels. The first six channels have balanced XLR microphone and TRS balanced inputs, input trim control, three-band EQ, master volume and trim set light. The mono line inputs on channels 5 and 6 are pre-EQ’d for Hi-Z instrument level input, making them an ideal place to start when looking for that perfect live acoustic guitar or direct bass sound. When the input trim level is properly set, users will have ample overall gain while taking full advantage of the new clip elimination circuit which makes it virtually impossible to distort the input of the microphone and instrument channels.

In addition to the 6 mono microphone channels, the M810 has two discrete stereo input channels (channel 7 & 8, 9 & 10) each with three-band EQ and stereo TRS balanced inputs. Both stereo channels have an additional XLR balanced microphone input, making for a total of 8 potential microphone inputs, or 6 mono microphone inputs and two stereo line inputs.

MicroMIX Series Overiew

Specifications
Number of Channels 10
Mono Channel EQ Low, Mid, High
Stereo Channel EQ Low, Mid, High
Channel Effects All Channels
Monitors Effects Yes
Balance Controls Ch. 7 - 10
Pan Controls Ch. 1 - 6
Channel Overload Protection Ch. 1 - 6
Inputs - XLR (bal) 8
Inputs - 1/4" 10
Inputs - RCA (unbal) 1 Pair
Mute Switches Global 1 - 8
Activity / Solo LED Trim Set Ch. 1 - 6
Clip /Mute LED All Channels
Phantom Power 48V + LED Indicator
Internal Effects Digital 16 Bit; 255 Effects
Auxiliary Sends Effect - Monitor
Effects Send Yes
Effects Return Internal
Effects Return to Main Yes
Effects Return to Monitor Yes
Reverb / Effects Footswitch Yes
Record Outputs Stereo RCA Pair
Max Gain to Line Out -Mic Input (dB) +84
Max Gain to Line Out -Line Input (dB) +82
Master EQ -1 (type /Channels /Range - dB) Graphic 9 band (160hz-6.3khz) +2 band Shelving
Monitor EQ -1 (type /Channels /Range - dB) Graphic 9 band (160hz-6.3khz) +2 band Shelving
Main Outputs ( Line Level) 2 x 1/4inch TRS
Main Amp Inputs (Line Level) 2 x 1/4inch TRS
Monitor Outputs (Line Level) 1 x 1/4inch TRS
Outputs - Amp A - 1/4" Jacks 2
Outputs - Amp A - Speakon 4-pin 1
Outputs - Amp B - 1/4" Jacks 2
Outputs - Amp B - Speakon 4-pin 1
Mixer - Signal to Noise Ratio (dB) 105
Mixer - Frequency Response (Tone and EQ Flat,+/-2dB) 20 - 20,000
Mixer - Input Referred Noise to line out, @ 150 Ohms (dBv) -119
Mixer THD (Main out w/ -10dB input) 0.01%
Amp A - Power Output @ 8 Ohms (0%1"THD, 1kHz) 250
Amp A - Power Output @ 4 Ohms 400
Amp A - Power Output -other 400 @ 2 ohms
Amp B - Power Output @ 8 Ohms (0%1"THD, 1kHz) 250
Amp B - Power Output @ 4 Ohms 400
Amp B - Power Output -other 400 @ 2 ohms
THD - 1kHz (dB) 0.1%
THD - 20Hz-20kHz (dB) 0.5%
Hum and Noise (un / Aweight -dB) -101 / -107
Typical crosstalk -1 kHz (dB) better than -60db
Input Impedance - Bal/Unbal (Ohms) 20k / 10k ohms
Input Sesitivity (Vrms Sine) 1.4
CMRR @ 60Hz (min/typ) -37db / -60db
Max Votage Gain (dB) 29
Power Consumption (typ/max) 4.2A @ 60Hz / 2.2A @ 50Hz
Protection Thermal, Short Circuit, Impedance Overload
Cooling 2 x 80mm Fans
Transformer Type Toroidial
Finish Grey and Black Powder Coat
Chassis Construction Steel and Aluminum
Rackmount Yes (Kit Available)
Other Features Tiltback or Upright Wedge Angles
Dimensions (DWH, inches) 11.1 x 18.6 x 11
Dimensions (DWH, cm) 28 x 47 x 28
Weight (lbs/kg) 27 / 12

MicroMIX Series Overiew
For simple plug-and-play, nothing beats the Yorkville MicroMIX™ series. They offer high performance in complete, compact, flexible packages. Although simple, MicroMIX™ series mixer are not short on features. Ease-of-use and practical designs are at the center of the MicroMIX™ line of powered box mixers. Whatever you require, Yorkville has the right MicroMIX™ for you.
MicroMIX Series Features
Yorkville's MicroMIX™ powered box mixers offer more power, more features and are more affordable than ever. Standard features include:

scratch resistant front panels
metal phone jacks
graphic EQs*
built-in limiter
phantom power
onboard reverb/effects*
balanced XLR, 1/4" phone and dual RCA inputs
19" rackmount versions**
gold plated connectors
All Yorkville Box Mixers feature 3/4" plywood construction covered with blue/black carpet (excluding rackmount version). Chassis are constructed of heavy metal to withstand all the rocking and rolling associated with life on the road while inside we use high quality epoxy circuit boards coated with thick copper laminate and precision, 0.1-1% tolerance, low noise components. A large heatsink and a variable speed DC fan (MP8DX) ensure that the mixers keep their cool. Of course MicroMIX™ mixers also come with Yorkville's standard two year (even if you break it!) transferable warranty in the USA and Canada. These are just a few of the characteristics which make MicroMIX™ mixers the "Best Bang for the Box".

*except MM4
**MM4R and MP8DR only